- 手機：
- 18631165157
- 電話：
- 18631165157
- 郵箱：
- 415130881@qq.com
- 地址：
- 安國市南陽工業區
安裝臥式泡沫泵的機械密封需要遵循以下步驟：
1. 準備工作：在開始安裝之前 2. 拆卸舊的機械密封：如果泵上已經有舊的機械密封，請先將其拆除。通常，這需要松開固定螺栓，然后取出舊的密封件。在拆卸過程中 3. 清潔軸和密封座：在安裝新的機械密封之前，請確保泵軸和密封座表面干凈 4. 安裝密封墊片：將密封墊片安裝在密封座上。確保墊片與密封座表面緊密貼合 5. 安裝機械密封：將機械密封安裝在密封座上。確保密封件與泵軸之間有一定的間隙 6. 安裝彈簧：將彈簧安裝在機械密封上 7. 固定機械密封：使用螺栓和螺母將機械密封固定在密封座上 8. 檢查安裝：在啟動泵之前 9. 啟動泵：在確認機械密封安裝正確后 通過以上步驟 To install the mechanical seal of horizontal foam pump, the following steps should be followed: 1. Preparation: Before starting the installation, please ensure that you have prepared all necessary tools and parts. This includes mechanical seals, sealing gaskets, bolts, nuts, springs, etc. In addition, it is necessary to ensure that the shaft and sealing seat surfaces of the pump are clean and free of oil stains. 2. Disassemble the old mechanical seal: If there is already an old mechanical seal on the pump, please remove it first. Usually, this requires loosening the fixing bolts and then removing the old seal. During the disassembly process, please be careful not to damage the pump shaft or sealing seat. 3. Clean the shaft and seal seat: Before installing a new mechanical seal, please ensure that the surface of the pump shaft and seal seat is clean and free of oil stains. You can wipe it with a clean cloth or clean it with a solvent. 4. Install the sealing gasket: Install the sealing gasket on the sealing seat. Ensure that the gasket is tightly attached to the surface of the sealing seat without any gaps. 5. Install mechanical seal: Install the mechanical seal on the sealing seat. Ensure that there is a certain gap between the seal and the pump shaft to generate frictional heat during operation and prevent premature wear of the seal. At the same time, ensure that the seal is tightly attached to the sealing seat without any gaps. 6. Install the spring: Install the spring onto the mechanical seal. Ensure that there is a certain gap between the spring and the seal to generate frictional heat during operation, thereby preventing premature failure of the spring. 7. Fixed mechanical seal: Use bolts and nuts to secure the mechanical seal to the seal seat. Ensure that the bolts are tightened, but not too tight to avoid damaging the mechanical seal. 8. Check installation: Before starting the pump, please check the installation of the mechanical seal. Ensure sufficient clearance between the seal and the pump shaft, a tight fit between the seal and the seal seat, and moderate tightening of bolts. 9. Start the pump: After confirming that the mechanical seal is installed correctly, the pump can be started for trial operation. During operation, please pay attention to the working status of the mechanical seal. If there are any abnormalities, please stop the machine for inspection in a timely manner. Through the above steps, you can complete the mechanical seal installation of horizontal foam pump. During the installation process, please be careful to avoid damaging the pump shaft, seal seat, or mechanical seal. If you have any questions, please consult a professional. 上一條 ： 臥式泡沫泵的氣蝕余量是多少 下一條 ： 臥式泡沫泵性能參數
18631165157