- 手機：
- 18631165157
- 電話：
- 18631165157
- 郵箱：
- 415130881@qq.com
- 地址：
- 安國市南陽工業區
臥式泡沫泵的使用與維護
臥式泡沫泵是一種常用的消防設備，主要用于輸送含有泡沫的磨蝕性或腐蝕性渣漿 在使用和維護臥式泡沫泵時 1. 安裝前檢查設備外觀是否有損壞或變形 2. 確保泵與底座之間的配合緊密，以免在使用過程中發生松動。 3. 注意電機的接地線是否已連接好，以確保安全。 4. 確認泵的進出口方向是否正確，以免影響泵的性能。 5. 確保泵的進出口管道已正確連接，否則會影響泡沫滅火劑的輸送和噴射效果。 6. 檢查泵的電源線是否符合要求，并按照要求接好電源線。 7. 檢查泵的密封性能是否良好，如果泵的密封性能不好，會導致泡沫滅火劑泄漏，影響使用效果。 8. 避免磨擦，否則應調整葉輪間隔。 9. 脫開泵與電機間的傳動，檢查電動機轉向，要保證泵按泵體上所標出的箭頭方向轉動，注意泵不允許反向轉動，否則葉輪螺紋會脫扣，以導致泵損壞。 10. 皮帶傳動時，泵軸和電機軸要平行，并且應調整槽輪位置，使與三角帶其互相垂直，以免引起劇烈的振動和磨損 Use and maintenance of horizontal foam pump Horizontal foam pump is a commonly used fire-fighting equipment, which is mainly used to transport abrasive or corrosive slag slurry containing foam, such as in metallurgical, mining, coal, chemical and other industrial sectors. In addition, AHP horizontal foam pump is also a common fire-fighting equipment, which is used to transport foam extinguishing agent. When using and maintaining the horizontal foam pump, pay attention to the following points: 1. Before installation, check the appearance of the equipment for any damage or deformation. If so, replace or repair it in a timely manner. 2. Ensure a tight fit between the pump and the base to prevent loosening during use. 3. Pay attention to whether the grounding wire of the motor is properly connected to ensure safety. 4. Confirm whether the inlet and outlet directions of the pump are correct to avoid affecting the performance of the pump. 5. Ensure that the inlet and outlet pipes of the pump are correctly connected, otherwise the delivery and spraying effect of foam extinguishing agent will be affected. 6. Check if the power cord of the pump meets the requirements and connect the power cord as required. 7. Check whether the sealing performance of the pump is good. If the sealing performance of the pump is not good, foam extinguishing agent will leak, affecting the use effect. 8. Avoid friction, otherwise adjust the impeller spacing. 9. Disconnect the transmission between the pump and the motor, check the direction of the motor, and ensure that the pump rotates in the direction indicated by the arrow on the pump body. Note that the pump is not allowed to rotate in the opposite direction, otherwise the impeller threads will trip, causing damage to the pump. 10. When using belt transmission, the pump shaft and motor shaft should be parallel, and the position of the groove wheel should be adjusted to be perpendicular to the V-belt to avoid severe vibration and wear. 上一條 ： 立式泡沫泵葉輪工作怎么消除泡沫 下一條 ： AF泡沫泵有沒有吸程
18631165157